M2N68-LA MANUAL PDF

Asus M2NLA Pdf User Manuals. View online or download Asus M2NLA User Manual. Looing for a install manual for the Asus M2NLA Narr5 , so I can check the start switch. I need the pin out. ASUS HP Motherboard M2NLA NARRA2-GL8E AM2 Systemboard Related Links: Specifications, Driver Downloads and CPU Support List (via ).

Author: Zulkit Dogis
Country: Pakistan
Language: English (Spanish)
Genre: Business
Published (Last): 5 March 2009
Pages: 223
PDF File Size: 11.32 Mb
ePub File Size: 7.91 Mb
ISBN: 609-4-75278-665-3
Downloads: 77270
Price: Free* [*Free Regsitration Required]
Uploader: Kazrazilkree

The CPU fits in only one correct orientation. Locate the CPU socket on the motherboard. M2NLA Narra 3 3. Position the CPU above the socket such that the CPU corner with the m2n68-ka triangle matches the socket corner with a small triangle.

HP and Compaq Desktop PCs – Motherboard Specifications, M2N68-LA (Narra2)

Carefully insert the CPU into the socket until it fits in place. Gold triangle Small triangle 5. The lever clicks on the side tab to indicate that it is locked. Install a CPU heatsink and fan following the instructions that came with the heatsink package.

For optimum compatibility, we recommend that you obtain memory modules janual the same vendor. Failure to do so can cause severe damage to both the motherboard and the components. Unlock a DIMM socket by pressing the retaining clips outward. Unlocked retaining clip 3. Support the DIMM lightly with your fingers when pressing the retaining clips.

The DIMM might get damaged when it flips out with extra force. M2NLA Narra 3 4. The figure shows a graphics card installed on the PCI Express x16 slot. The figure shows a network card installed on the PCI Express x1 slot. M2NLA Narra 3 5.

  CANON XEED SX7 PDF

Asus M2NLA Manuals

Turn OFF the computer and unplug the power cord. Remove the onboard battery.

Plug the power cord and turn ON the computer. Removing the cap will cause system boot failure! To erase the password: Move the jumper cap from pins Normal to pins Clear Password. After the computer m2n68-laa up, turn OFF the computer. Move the jumper cap from pins to pins Side Speaker Out port gray. This port connects to the side speakers in an 8-channel audio configuration.

Rear Speaker Out port black. This port connects to the rear speakers on a 4-channel, 6-channel, or 8-channel audio configuration. Line In port light blue. Line Out port lime.

This port connects a headphone or a speaker. In 4channel, 6-channel, and 8-channel mode, the function of this port becomes Front Speaker Out. This port connects a microphone.

M2NLA Narra 3 Refer to the audio configuration table for the function of the audio ports in 2, 4, 6, or 8-channel configuration. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. Orient the red markings on the floppy ribbon cable to PIN 1.

This prevents incorrect insertion when you connect the IDE cable. The power supply plugs are designed to fit these connectors in only one orientation.

  IRIVER T10 MANUAL PDF

Find the proper orientation and push down firmly until the connectors completely fit. The minimum recommended wattage is W, or W for a fully configured system.

The system can become unstable and might experience difficulty powering up if the power supply is inadequate.

HP and Compaq Desktop PCs – Motherboard Specifications, M2N68-LA (Narra6)

The system may become unstable or may not boot up if the power is inadequate. M2NLA Narra 3 13 4. Doing so will damage the motherboard!

Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of m2n8-la cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers!

DO NOT place jumper caps on the fan connectors. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. It’s a community-based project which helps to repair anything.

admin